BENEPARTS MACHINERY 
 Tel: +86-574-88167027       E-mail: sales@bycasting.com
You are here: Home » Products » Ground Engaging Tools » Bucket Teeth » 230SP Flexpin Style Tooth Design Sharp Penestration 23PN

230SP Flexpin Style Tooth Design Sharp Penestration 23PN

230SP Flexpin Style Tooth Design Sharp Penestration 23PN
Material:
Availability:
  • 230SP

Product Description

Part Number: 230SP

Material: Alloy steel

Weight: 1.2 kgs

Correspondent Pin: 23PN

Correspondent Adapter: 2740-23 / 834-23


Material: Alloy steel

Chemical component: Carbon, Silcon, Manganese, Sulfur, Phosphorous, Chrome, Molybdenum, Nickel


Teeth

Hardness: 45~55HRC

Impact: 8~25J


Adapter

Hardness: 25~35HRC

Impact: > 15J


Casting Type: Fine Casting / Sand Casting / Film Covering Sand Mold

Heat Treatment: Normalising, Quenching, Tempering


230 Series Teeth

230CF: Cast Flared Tooth

230CHF = 23HXF: Flared Flexpin Style Tooth; Heavy Duty Version of the 230CF Tooth

230CHFC: Flared Corner Style Tooth; Heavy Duty Version of the 230CF Tooth

230CLAW: Stronger Version of the Cast 230TF Fangs Tooth

230CPE: Heavier Version of the Sharp Penetration 230SP Tooth

230CSP: Cast Sharp Penetration; Other Part Number Associated with the Original 230SP

230CST: Cast Star Ripping Design; Other Part Number Associated with the Original 230ST

230CTT: Forged Centerline Twin Tiger Tooth; Heavier Version of the Twin Tiger 230TT Tooth

230SP: Sharp Penetration; Flexpin Style Tooth Design

230ST: Uniforged Flexpin Style Tooth Design; Penetration Version of the General Purpose 230SP Tooth

230T9: Forged Tiger Tooth; Sharper Penetration Version of the Star 230ST Tooth

230TF: Fangs Style Penetration; Heavy Duty Rock Application; Forged 230CLAW (Curved Profile) Design

230THD: Cast Single Sharp Design

230TL: Long Sharp Tiger Penetration

230TR3: Triple Tiger Trident Tooth; Self-sharpening Design; Centerline Design Allows Reversible Fit

230TT CLAW: Twin Tiger Claw (Fangs Style) Penetration

230TT7: Twin Tiger Penetration; Sharper Penetration Version of the Twin Tiger 230TT Tooth

230TW: Cast Twin Sharp Design

230WTL: Long Twin Tiger Penetration; Sharper Penetration Version of the Twin Tiger 230TT Tooth

23SP: Sharp Penetration; Fabricated General Purpose Sharp


The Maintenance of Bucket Teeth & Adapters (Ground Engaging Tools)

When the bucket teeth contact the material surface, because of the fast speed, the tip of the bucket teeth will be subjected to a strong impact load. If the yield strength of bucket tooth material is low, plastic deformation will occur at the tip. With the increase of excavating depth, the pressure on the bucket teeth will change.


The excavator/loader bucket control is the key to utilize the bucket teeth. The operator should try not to retract the bucket when lifting the boom. The operator should pay attention to the coordination of actions. Some of them throw the bucket on the rock during the action of expanding the arm, this will break the arms & cracks will occur on the bucket teeth.


In the daily maintenance, please spend 2 minutes to examine the bucket. The key point is to check if the bucket wears equally & any cracks has been occurred. If the status is horrible, you should carry out structural reinforcement immediately. If there is a crack in the bucket body, welding repair should be carried out immediately to prevent the increase in the length of the crack. In addition, you have to check the fitness of bucket teeth. If the teeth are loose, they should be tightened right away.

Before the bucket teeth reaches their service life, built-up welding is required. By the way, no bucket tooth made of a certain material can be applied to every kinds of work conditions, the teeth should be reasonably selected based on different work conditions to avoid unnecessary abrasion.


The bucket teeth on both sides of the excavator are worn about 30% faster than those in the middle. The bucket teeth on both sides and in the middle can be interchanged for further use, so as to reduce the repairs times and indirectly increase the service life of the bucket teeth.

It is recommended to replace the adapter after 10% of worn. There is a large gap between the worn gear base and the bucket teeth. The bucket teeth are easy to break due to the change of the stress point.


When you leave bucket teeth to wear down for too long, the moving range of excavator bucket will increase dramatically, and your excavator will take far longer to complete tasks and will use more fuel too. Dull bucket teeth will result in greater percussive shock to be transmitted via the bucket to the digging arm and undercarriage of the machine. This can result in damage to the equipment and accelerated wear to the other undercarriage components. It is necessary to immediately remove and replace the new bucket teeth.

CONTACT US NOW

If you would like to have a question then get in touch today, we are ready to assist 24/7.
We welcome your cooperation and we will develop with you.
 Factory-direct Connectivity Solutions.
High quality, Competitive Price.
​​​​​​​ Custom-tailored solutions.
​​​​​​​ Problem-solving approach.
Product Inquiry

PRODUCT CATEGORY

ABOUT BENEPARTS

Ningbo Beneparts Machinery Co., Ltd is a manufacturer in China armed with more than 30 years of successful experience in Ground Engaging Tools & Undercarriage Parts.

GET IN TOUCH

   Room 2609, Huiya International Building, No 1107 Tiantong North Road, Ningbo, Zhejiang, China
   +86-574-88167027
   sales@bycasting.com         
CONTACT US
Copyright  2020 Ningbo Beneparts Machinery Co., Ltd   Support by haipai